Видео

Awesome work! Whats the model of excavator you're using? Im thinking of buying one to get this done. A used one is less than the entire job and I can use it for other projects. TIA

Great video, very informative! Thanks for sharing your knowledge! Semper Fidelis Bruce.

Of course you can do it on the ground. I did the timing chains and phasers on the ground, which requires taking the pump off just to do it (even though i just left mine tucked in back)

Just took mine out (2016 AWD) out with the help of this video. Thank you. I struggled until removed a heat shield (2x10mm bolts). Once I did that, it took 5mins to get out. You’ll need a looooong extension with a swivel end to get that back bolt.

Good progress

Great job, correct way to do it. I’m doing this at my house in May

That's ridiculous. Can the police legally refuse to follow through on charging a criminal if they already know who did it? If they DO have that discretion, it seems ripe for abuse. If they happen to not like you for some reason, they could just allow you to be robbed, maybe even killed. Scary.

Wish you were in Ohio 😂

Is your Chime louder ??

I know its been a couple years, was wondering if you still have the van and if so how its coming

Trying to do this on my 2017 and I can’t get my pump out this way any suggestions?

MOFO THANK YOU SR !!!

I've found the solution for your task after thoroughly reviewing your social media presence and analyzing your RUclips channel. Your RUclips videos are impressive and enjoyable. However, to enhance the visibility of your channel and potentially make it go viral, certain updates are crucial-especially focusing on SEO and more. I'm prepared to assist by optimizing your videos for SEO and promoting your content if you're interested.

Dumb question? Why didn’t you all install drain pipe and or elephant trunk? Was that because it might not be able to day light?

You said a few times "inspection" what type and who would be doing the inspection. Thank you in Advance..

What does this cost to have done? I need it done to one side of my house. I have some water that leaks into my garage and want to have this remediated before I epoxy my garage floor.

Skilled equipment operator. Nice job going under the air conditioning and around the pipes with no damage.

Thanks. I just got a 5th gen ram and was looking for info on running my dash cam power. This is exactly what I was looking for.

It’s a bitch on your back

At those temps that kind of work is brutal on the fingers.

Great video! Thank You!

I have 1 coming in next week so I haven't seen it yet but my question is if you took the complete tie rod assem. inner and outer off would it fit through the wheel well then?

Just did mine this weekend. Your advice helped. Seemed like it took forever to get it out but getting it back in with a piece of cake👍🏻

Question? I have a 2014 traverse. It has been leaking steering fluid at a rate of half a quart about every two months. I degreased the undercarriage to try and identify exactly where the leak is coming from but still can't quite see it. It's definitely coming from the pump and not the rack but my question is, should I just go ahead and replace the pump or should I do anything more to try and diagnose the issue? I do all of my own repairs because where I live there are no mechanics that are trying to do a good job well done without robbing you blind first. I guess a more indepth explanation of my question would be if I replace the pump is there anything else I need to watch out for that it may be leaking from that may not directly be the pump itself?

Awesome. Great video!

It would be nice to see a step by step on the finishing of the ceiling including tools needed and materials list. Also how did you finish the walls before screwing in those 3/4 strips for mounting the bed. In other words, what are you screwing them into? Thanks!

God bless this guys soul I was getting ready to take off the engine mount ..

That’s how I did it

What if a person had a step van. With endless supply of electricity, to live in year around without solar panels. For the ac, for refrigeration. Be like, what the model T, was to cars, dependable. Comfortable. It could have it's own heat supply or a small bullet stove, sucking air from the bottom pipe.

Where did you get the bulbs for the turn signal and marker light

Ok here is the absolute easiest way. Remove belt. Unbolt passenger sway bar link from strut. Unbolt tie rod from knuckle. Remove right side subframe bolts, don't touch left side to keep subframe position. Lower subframe as far as it will go. Remove flare nut, remove 10mm holding return elbow. Pump falls right out through wheel well. Takes 30 minutes.

not helpful when you don't actually show the work.

There is a power post by fuse panel… no need to drag wire across engine bay like that.

Nice machine. Skilled operator.

Skilled with the machine!

Hows the van going?

how did you unplug the electric wire? it dont seem to come off?

Could you wire this to one of the fog lights? So you don't need a switch.

What drill size did you use?

Since you all are in the know and before I commit my day to doing this, can you tell me the symptoms that lead you down this path? My steering wheel is shuddering, bouncing, jerking (whatever adjective works) when I turned the wheel while sitting idle. I'm not hearing anything from under the hood but it's always moaned.

Next upload when?

bamb i from fnf r eal

Thank you James

You just save me 5 hours of my day after 5 hours not watching this video

We have video of fawn drinking from a pasture sprinkler head.

Nice job. Paint the rest of the frame.

Can you drop the link for ur line out converter please

I work with a guy who was at a HD truck repair shop. Tech got a phone call and rolled out from under the truck, walked to his phone, then there was a loud crash. The jack stand failed, and the truck fell and would've killed him. Moral of the story: don't trust your equipment too much. Make sure jacks and stands are rated for the load you're trying lift. Most important: don't trust Chinese manufacturing. Stay safe.

Take the pully off also with a puller,it can be done if you get it in position,then comes right out.No need to take anything apart.This is great idea also.If you don't have a lift.

Just did this on my back. 2013 Traverse AWD. Took about 3 hours. The pump slides out easy through where you showed. Remove the elbow from the pump first (held on by 10mm bolt) and it'll slide out and in 2 minutes tops. No need to drop frame or driveshaft. The hardest part honestly is getting the line nut out and putting the hose clamp back on (I highly recommend replacing it with a screw-type clamp).